Getting Familiar with Plumbing: Your Starting Point for Bathtub Installation
Getting Familiar with Plumbing: Your Starting Point for Bathtub Installation
Blog Article
How do you feel about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't precisely brain surgery, yet it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is likewise a moderately difficult project. If the old tub is easily accessible, the project can move immediately; if you have to open a wall surface to remove the old tub and place the brand-new bath tub, the task is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need an assistant to vacate the old bathtub and embeded in the brand-new one. Make certain you have certified yourself for the work and are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed task, it is much better to take into consideration employing one prior to you start. Opportunities are you may require an expert plumber to make tube links.
This write-up will certainly aid you mount a new tub in your shower room if you have actually already gotten a brand-new bathtub as well as do not require to transform the arrangement of your previous water system pipelines.
Your tools as well as material checklist should comprise the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of removing the existing taps can be fairly problematic because of the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a towel all set for the remaining water that will come from the pipes. As soon as the supply pipes have actually been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old securing substance.
Before proceeding to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making certain that the washers remain in location between the tap and also the sink. Secure the faucet in place with the producer offered backnut. Once the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be attached to the faucet finishes initially, tightening only by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the bathtub in the needed position. The wood boards are handy in equally spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto four small factors.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the bathtub till the level reads degree.
To install faucets, fit all-time low of the outermost adaptable tap port to the suitable supply pipeline by making a compression join; then do the same for the various other faucet.
Turn on the water as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Fill up the bath tub and additionally inspect the overflow outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bathtub must wait up until the tub has actually been used at the very least once as this will certainly settle it into its final placement.
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps device to prevent stress on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you use every one of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath should now prepare to be suited its final placement.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture an inflexible seal, causing the water to permeate the wall between the bathroom and the tiling, causing difficulties with wetness as well as possible leaks to the ceiling below.
You can choose from a variety of coloured sealants to assimilate your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can break rather very early if you do not consider this movement prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I discovered that review on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while browsing the internet. Liked our blog posting? Please share it. Help somebody else discover it. Many thanks for taking the time to read it.
Quality fix? Call! Report this page